Gmt 400 ls swap.

I have a 94 and did an LS3 swap. it works great, except I cant get my oil pressure gauge to work. When I crank the truck it pegs out. Any suggestions would be appreciated!Black/white stripe is the ground, purple is the fuel sender wire to the guage, and the gray is the power supply. after tapping in my fuel pump relay to the gray wire, my guage didnt work. i snipped the black and white wire, and put a hoop connector on it, and grounded itnear one of the bolts for the pedal assembly. works fine now. hope that ...1996-2000 OBS / GMT400 Gen3 LS Swap Info. Here I will go over a swap I completed on a 1998 C1500 pickup. It originally had a 4.3L Vortec and swapped to a 2005 5.3L LM7 with drive by wire. I will go over the way I did the harness integration to all factory functions on the 1998. AC, Cruise, all gauges, so on.Reaction score. 32. In my opinion before pulling the 350, mark all your wires. You will reuse the temp sender and oil sender for the gauges. Also need the wire down to the starter. My harness is a modified stock LS harness, and it is stand alone. I'm still figuring out how to get my speedometer to work.I used this truck as a daily driver for a year and a half and I fell in love with the truck as some people do. But now the truck sits in my driveway because of a few problems like Brakes, Transmission, Engine. I have done some research and decided to swap the old 4.3 for ls style truck motor. and I would like some info on doing the swap.

Texas. Had my 96 sierra ls swapped upgrades truck Norris nsr cam ls1 intake and fuel rails with 42 lb injectors. Running fine for about 5 miles then begins to sputter and run rough. Shop that did swap which was a zero miles swap engine rebuilt retuned engine but still running rough after about 5 miles . Mechanic states that exhaust is causing ...Well its time for the old and leaky 350 to be pulled. I have most of my parts gathered up and ready to go, including but not limited to.... -2002 5.3L. -Dirty Dingo Motor mounts. -JEGs crankshaft spacer. -0411 PCM. -'05 truck fans. Motor will be pulled today and major engine bay cleaning will ensue. So far I'm still well under $1000 for the ...Apr 5, 2021 · 25. Reaction score. 14. Location. 32735. I'm swapping a new motor into my 98 k1500 as the stock 5.7 Vortec started knocking right after I was done putting a new tranny in and I'm at a crossroads. I have access to two motors. One is an aluminum block 5.3 and the other is a 5.7 ls1.

8. Reaction score. 4. Location. Georgia. I have a 1998 vortec 5.7 with a 4l60e i’ve been looking into a ls swap but i don’t even know where to start don’t have much mechanical experience or know what to get can someone tell me everything that’s needed i want to do it myself to learn location and names of things thanks. Sep 17, 2022. #2.Since 2500 LSx Suburbans in GMT800 are either (1) sacked out beyond belief, (2) unobtainum priced, or (3) non-existant I'm thinking a GMT400 1/2 Suburban. I really like this body style, not a huge fan of GMT900 truck looks. Additionally, I love LS and they definitley beat cap/rotor/old small block ignition systems.

Joined. Dec 18, 2013. Messages. 199. Reaction score. 3. Got a head start on parts and ordered my mount plates, fuel pump, 98 camaro/firebird temp sensor, and my oil sender adapter. It will be anouther month or so before I get my motor and I'm ordering a flip kit tomorrow witch will be here well before the motor.Black/white stripe is the ground, purple is the fuel sender wire to the guage, and the gray is the power supply. after tapping in my fuel pump relay to the gray wire, my guage didnt work. i snipped the black and white wire, and put a hoop connector on it, and grounded itnear one of the bolts for the pedal assembly. works fine now. hope that ...Flex-a-lite has great products. I just installed one of their syclone fans in my truck, as well as the controller unit from Flex-a-lite as well. Works great, and moves a ton of air, and the controller gives you the option of choosing what temperature the fan turns on at. Oct 17, 2015. #4.Jan 24, 2023 ... 1991 Chevy OBS Cheyenne V8 LS Swapped Build Remove and Replace Front Grill Upgrade Swap ... HOW TO GRILLE SWAP ANY 88-93 GMT400 TO 94-98 ( ...Gmt 400 LS swap in 1 week - YouTube. Busted to Built. 2.27K subscribers. 69. 4.9K views 2 years ago. Throwing in an engine and trans with over 300k into a truck …

1992 K1500 LS swap information: The recipient of the swap is a 1992 GMC K1500 (4x4) 5.7L, 700R4/4L60 trans, 241C transfer case, regular cab shortbox: The donor truck was a 2000 Silverado 1500 (4x4) 5.3/LM7, 4L60E trans, 246 transfer case: This write up is a description of what was done and what I chose to use for this swap. There are many other ...

Remove all the emissions pins from the LS1 harness. If you are using a 4l60 with your LS engine and the vehicle you are working on had a 4l60 then keep the factory transmission pins and swap them into the LS harness. If you are using a 4l80 then use the transmission pigtail harness you have (assumedly a 6.0/4l80 takeout).

Dec 2, 2009 · Tape electrical tape (3M or better: throw away the generic stuff – it flakes off after a year and gets everything sticky) around the base of the two wires tightly. Fold the copper connection over onto the newly taped insulation, and tape over it carefully, tightly and repeatedly to make it waterproof. 1996-2000 OBS / GMT400 Gen3 LS Swap Info. Here I will go over a swap I completed on a 1998 C1500 pickup. It originally had a 4.3L Vortec and swapped to a 2005 5.3L LM7 with drive by wire. I will go over the way I did the harness integration to all factory functions on the 1998. AC, Cruise, all gauges, so on. Let's start with the basics: You're more than likely mispronouncing it. Photo courtesy of Medellin.travel Rather than saying Medellín like “meddling,” the two ls are actually prono...25. Reaction score. 14. Location. 32735. I'm swapping a new motor into my 98 k1500 as the stock 5.7 Vortec started knocking right after I was done putting a new tranny in and I'm at a crossroads. I have access to two motors. One is an aluminum block 5.3 …LS swap 5.3/4l80e/bw4401 4x4. NO START ISSUE!!! built the harness via instructions from lt1swap.com, pcm is hptuners with vats, egr, secondary o2's programmed out. new install, does crank over, fuel pump is pressuring up for 2 seconds then off, checked crank sensor, have voltage and AND ground, tested sensor it is working, checked voltage and ...25. Reaction score. 14. Location. 32735. I'm swapping a new motor into my 98 k1500 as the stock 5.7 Vortec started knocking right after I was done putting a new tranny in and I'm at a crossroads. I have access to two motors. One is an aluminum block 5.3 …A lot of people say to use the 1" set back motor mount adapter plates. I did, and ended up having to drill new holes for the trans cross member 1" behind my original holes. No big deal. Since the swap, I've swapped out my stock exhaust manifolds for the schoenfeld long tube headers for LS swaps into 88-98 pickups (1302LS1 i think is the part ...

All gauges work just like factory. Customer must ship the C/K harness and the LS harness from the engine there swapping. If you don't have the LS harness I can add all new …A little about my back ground. I work at Motech in Las Vegas NV. We do LS Swaps in JK Jeeps. About a year ago we started doing the Gen V engines and I really believe in these engines. The engines make incredible power and torque. It make torque at very low RPM's which moves the heavy jeeps effortlessly. The 6L80e is still looked at like …This one has been in my 97 for almost two years. It's about 7/8" thicker than the factory radiator. Shroud fits perfect. Even at altitude (where the air is a lot thinner) it never gets above 195* w/ the AC on and a full load of …Reaction score. 335. Location. Michigan. To swap in the nv4500 you need the transfer case that was hooked to it. The one in your truck has a different input spline size. Going 6L look for a k2500 in the yards that was hooked to a 6.0 for the nv4500. For an LQ9 I think you are looking for Escalade or Denali donars.I have a 93 C1500. Has any one done an LS swap in CA, if so what are the requirements to pass emissions? Also what is the best LS to swap in?Ls swapped using the 411 pcm in my 98 silverado. Tuning with hp tuners, does anyone know the correct setting to get my fuel gauge to work? Jan 4, 2022 #2 C. codemain19 Newbie. Joined Nov 6, 2019 Messages 1 Reaction score 0 Location 17813. Following working on mine as well right now. Jan 5, 2022Jan 10, 2022 · 3,236. Location. Georgia. Pretty much what frank said and the tach, speedo signal will come from the pcm. Get adapter for oil sending unit. And on coolant temp you can add a stock range sensor to pass side of ls or you can change the ls temp sensor for the f body 3 wire but it gauge is off 10ish degrees.

I think the only year of the TH400 was the 1988 or 1988-1989 models. Your 1992 has a 700R4. I have no idea on what all is needed though. The 5.3L is an OBD-II engine, and if you can find a 4L60E that was originally paired to a 5.3L, if you swap over the computer and wiring harness, it might be a "bolt on" swap, since you are putting in a "matching" powertrain, and using the correct computer ...

April 2, 2023. The GMT400 platform has been one of the most iconic and influential truck platforms in automotive history. First introduced in 1988 and produced until 1999, the GMT400 was the foundation for some of the most popular trucks and SUVs of its time, including the Chevrolet C/K Series, GMC Sierra, Chevrolet Tahoe, and GMC Yukon.Jan 3, 2024 · Reaction score. 335. Location. Michigan. To swap in the nv4500 you need the transfer case that was hooked to it. The one in your truck has a different input spline size. Going 6L look for a k2500 in the yards that was hooked to a 6.0 for the nv4500. For an LQ9 I think you are looking for Escalade or Denali donars. 8. Reaction score. 4. Location. Georgia. I have a 1998 vortec 5.7 with a 4l60e i’ve been looking into a ls swap but i don’t even know where to start don’t have much mechanical experience or know what to get can someone tell me everything that’s needed i want to do it myself to learn location and names of things thanks. Sep 17, 2022. #2.Nov 19, 2020 ... How To Get Your LS Swapped OBS Gauges To Work. I also have a video of where to move all your wires to complete the swap.Bumping this as I am in the same situation. LS into 1996 K1500 with push button t-case AWD/4WD. I can have LS ECM or the vortec OE ecm control the 4L60E trans. I kept the entire vortec harness intact. Just like OP, I need to know what to do with the wires from the firewall to/from body control module/dash. Mar 26, 2024.455. Location. Texas. I used a relay on my 90 with a 6.0/4L65E. Relay pin 30 to key hot source, 87A (NOT 87) to PCM C1 pin 33 TCC, 85 to ground, 86 to the brake light signal from the brake switch. This will give your PCM the TCC signal when the brake is released and remove the signal when the brakes are depressed.Home. Forums. General and Off Topic. GMT400 Suburban with LS swap? redhat. Feb 17, 2022. redhat. Joined. Dec 7, 2012. Messages. 3,558. Feb 17, 2022. #1. I …If you want an improvement, I suggest the 8100 Vortec. If you can find one with the Van/GMT400 3500HD brackets it is actually an easier swap than the LS. It will …

Find a 5.3L using the same operating system and swap the engine segments. I did that when my buddy put a 6.0L in his truck. It already had an 0411 I had tuned. I swapped the tune from a 5.7L/4L60E to a 6.0L/4L80E. Personally I would go bigger than a 5.3L in truck but that is me.

Nov 9, 2014 · A lot of people say to use the 1" set back motor mount adapter plates. I did, and ended up having to drill new holes for the trans cross member 1" behind my original holes. No big deal. Since the swap, I've swapped out my stock exhaust manifolds for the schoenfeld long tube headers for LS swaps into 88-98 pickups (1302LS1 i think is the part ...

Ultimate GMT400 LS Swap Guide. I. Development and Design of the GMT400 A. Background and Origins. In the early 1980s, the truck market was rapidly …1996-2000 OBS / GMT400 Gen3 LS Swap Info. Here I will go over a swap I completed on a 1998 C1500 pickup. It originally had a 4.3L Vortec and swapped to a 2005 5.3L LM7 with drive by wire. I will go over the way I did the harness integration to all factory functions on the 1998. AC, Cruise, all gauges, so on.8. Reaction score. 7. Location. Missouri. 1995 ls (4.8) swapped, has efans. Everything on truck works as it should, only issue is getting efans to work with ac. I am using HP tuners, have pin 17 hooked to ac wiring, pin 55 grounded (totally stock 95 ac system). Still having issues, can’t get efans to kick on with ac, have system set to analog ...A 4L60 non-E does employ a controller for the torque converter control (TCC) solenoid. Stand alone controllers for the TCC solendoid are available from well-known sources for $200-400. This may be what stutaeng was referring to. The other aspect of your swap is the throttle valve (TV) cable.Dec 7, 2012 · Since 2500 LSx Suburbans in GMT800 are either (1) sacked out beyond belief, (2) unobtainum priced, or (3) non-existant I'm thinking a GMT400 1/2 Suburban. I really like this body style, not a huge fan of GMT900 truck looks. Additionally, I love LS and they definitley beat cap/rotor/old small block ignition systems. How do I make my 89's check engine light work with LS swap? Sorry if this is the wrong section for this question, but I figure it is swap related. I just picked up a clean 89 Scottsdale that has a 00' LS engine swapped in. It is using a stock 4.8 and ECU, and what I am told is a Painless harness.See full list on buildpriceoption.com Sep 30, 2021 ... Part 11: Today, the 1991 Chevy OBS project truck gets a new fuel pump capable of supplying fuel to the 5.3 that will be going in soon. Misc. Items: $50. Total: $3,049. TECH ARTICLE LS Swap into 88-98 GM Truck We have always wanted to build a 88-98 sport truck, and with the popularity of these trucks coming back, now was the perfect time. At the moment, these trucks are relatively cheap to pick up, and can be found with full power, AC, tilt, etc. I acquired a l94 motor I’m going to swap into my 89. I’ll be running a Holley terminator. Mild cam, DOD delete, stock heads, shorty headers, upgraded lifters, stock rotating assembly. I’m also swapping a 14 bolt to the rear for reliability over the 10 bolt. - What are the best motor mounts to use to adapt a LS to our trucks?

I'm Awesome. I am making this thread for my truck and other people that are doing ls swaps in their 96-98 obs. I am doing the swap in my 98 ext cab and wanted to resuse as much of the harness as possible. So I can have the factory looking swap and still keep everything clean. There are some sensors and and components that will require cutting ...Jun 7, 2019 ... ... (GMT400), this video is for you. The ... GMT400 Rear Disc Brake Conversion (Part 2) #ETCGDadsTruck ... LS Swap. TanTinPerformance•22K views · 35:05.Remove all the emissions pins from the LS1 harness. If you are using a 4l60 with your LS engine and the vehicle you are working on had a 4l60 then keep the factory transmission pins and swap them into the LS harness. If you are using a 4l80 then use the transmission pigtail harness you have (assumedly a 6.0/4l80 takeout).Instagram:https://instagram. maytag rinse and spin cyclehr access l brands phone numberillinois p ebt 2023 deposit datesdoes whatsapp calls show up on phone bill verizon 3. Reaction score. 0. Location. League City, Tx. Here's my current project that I'm working on. It's a 96 2 door Tahoe. It has a 08 Express Van 6.0 and 4L80e GEN 4, drive by wire, stand alone engine harness TSP 231/239 LS3 cam. huge learning experience.LT1Swap.com was already mentioned, but as spoke of, has a ton of info for wiring your "LS" type engine. Your can do it with four fuses and tie into your harness. Yes, locate and re-use your temp and oil sensors for the dash as the donor engine has two locations for temp sensors. Leave the Temp sensor for you engine in place, but go to opposite ... final exam tamujanumet coupon 2023 8. 5.3_silverado said: You must be registered for see images attach. You must be registered for see images attach. go to the junk yard and get the original fuel lines off a truck or Tahoe. And stop by the parts store and a 3/8 and a 5/16 compression Union. That's how I did mine and turned out great. kristi trinidad I have a stock 5.3, with stock manifolds. I used about 4" of the OE exhaust off the manifold, for the flanges and O2 bungs. The rest is 2.5 pipe, curved pieces from the scrap bin at an exhaust shop, off a 2010 Camaro. The straight sections are from the parts store. Two Dynomax race bullets.The time difference between Greenwich Mean Time (GMT) and Eastern Standard Time (EST) is 5 hours, according to the WWP’s Eastern Standard Time website. During Daylight Savings Time...LS engine swap : r/GMT400. r/GMT400 • 3 yr. ago. by karmagettin11. LS engine swap. Would any of you consider swapping your engine with something like a 5.7 LS 6? I have a 350 in mine and wonder what the equivalent is, specially since I can afford a 2-4 thousand dollar engine but not a $50,000 new truck. 5 comments Best Top New Controversial Q&A.